By Plumbing Guide for Installing a Bathtub
By Plumbing Guide for Installing a Bathtub
Blog Article
Everybody may have his or her own theory when it comes to Installing A Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bath tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is readily available, the project can relocate easily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit attempting it. As opposed to working with a service provider to take over a halfway-completed job, it is better to take into consideration utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have already acquired a brand-new bathtub and also do not need to alter the plan of your previous water supply pipelines.
Your devices and product list need to make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic as a result of the restricted access that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipes. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washers are in location between the tap as well as the sink. Safeguard the tap in place with the manufacturer supplied backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bath tub in the needed placement. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bathtub up until the level reads level.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other faucet.
Switch on the supply of water and also check all joints and brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as likewise check the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub should wait till the bath tub has been utilized a minimum of once as this will certainly resolve it into its final position.
Getting ready for the Setup
Firstly, the sustaining structure provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to prevent strain on the tub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall surface between the bathroom and the tiling, causing issues with wetness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Installing A Bathtub? Try to leave a short review further down. We would be delighted to listen to your opinion about this blog post. Hoping to see you back again soon. Do you know somebody who is fascinated with How to Install a Bathtub Yourself? Be sure promote it. We value reading our article about How to Install a Bathtub Yourself.
Plumbing crisis? Contact our experts. Report this page